Boarding Up Windows And Doors Tips To Relax Your Everyday Lifethe Only Boarding Up Windows And Doors Technique Every Person Needs To Be Able To > 자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

24 hour boarding up service Up Windows and Doors Before a Storm Hits

In the event of a storm, boarding up your windows and doors provides measurable protection from damage. You will need several items to accomplish this.

Take measurements of the width and height of the window, including the frame (not the trim or masonry that surrounds the window). Keep these measurements in mind so you won't forget.

Preparation

It is recommended to put up a board on windows and doors before the storm or another natural disasters strike. This will help prevent damage to property and will minimize the loss of life. Boarding up windows requires lots of preparation, such as purchasing and measuring plywood boards, and determining the exact size of each window to be covered. It takes time to cut and boarding up install the boards in a proper manner. Fortunately it is possible to make the process made simpler by preparing as soon as you hear of a storm that could be coming in your area. You can avoid stress at the last minute and make it easier service for boarding up windows both you and your staff.

Begin by listening to forecasters of the weather and following the guidelines set by your local government. The earlier you start the process the better, as it allows you plenty of time to gather and store the needed items without being pushed by a fast-approaching storm. It is possible that you will require a large amount of plywood to cover your windows, depending on the severity and imminence of the storm. To ensure you get the right size, you can use a tape measure to determine the height and width of each window opening. Be sure to include the trim or boarding up framing around each window, and any ledges with extended edges if they are applicable.

Then, determine the dimensions of the sheets of plywood you require by dividing your window's total width and height by two. For instance, if the width of your window is 16 inches, the thickness of each sheet should be 8 inches. If you have wood exterior, drill pilot holes into the plywood sheet that align with the window frame beneath to reduce splitting when you screw in the screws.

If you have a larger window than a single sheet of plywood can handle cut two sheets of plywood that are half as big as the window you want to use. Then place them side by side on the wall. Then, cut a piece of 2 by 4 in (5.1 by 10.2 cm) lumber to the length of the connecting edges of the plywood sheets and then place it on top of the seam. Then then, drive 2.25 in (5.7 cm) screws through the bracing and into the plywood sheet to join them together.

Materials

To ensure safety and security ensure safety and security, use only materials that are sturdy and will not be damaged or break in strong winds. Plywood is the most commonly used material for boarding up windows. It is simple to use, affordable, and easily available. Choose plywood that is of the exterior grade (CDX), as it is stronger and will contain fewer warps and knots. Hurricane or storm shutters are more durable options. They can be installed over windows that are already in place and offer better protection against shattered glasses and inclement weather.

Once you've determined the location of the window openings you can determine the height and width to determine the amount of plywood you will require. Utilize a power drill to drill pilot holes in the sheets of plywood around each window at intervals of two inches. Before attaching the plywood, determine and mark stud locations on the wall to ensure the boards will be fastened securely. If you have wood siding in your home, search for nailheads in order to determine stud location. You could also use your drill to determine the locations of studs. Make sure you drive the screws into the framing, not the sheathing or trim; a plywood panel attached only to these materials could be dangerous in winds that are strong.

If your window is too big for one sheet of plywood, cut two pieces of plywood that are each half of the size needed and join them with 2 by 4 inches of lumber. Label each piece of plywood to let you know what window it will be covering.

Make sure you use corrosion-resistant screws that are long enough to penetrate the sheathing and the studs to secure the plywood panels to your wall. Make sure to insert the screws into the studs such they're about half as deep as the thickness of the plywood however, be cautious not to go too deep and damage the underlying structure of your house.

You should also think about installing polycarbonate security glass such as DefenseLite on your windows that are primary. These transparent shields adhere to existing glazing to protect your windows and doors and are virtually indestructible, preventing criminals from breaking into.

Installation

If you reside or plan to move to an area susceptible to hurricanes and are worried about the threat of storms you should consider boarding up company near me up all your windows and doors. This task can be completed quickly and efficiently, but only if the plywood sheets are cut, measured and labeled prior to the storm.

You'll require other tools as well, including drills, saws (or an hammer that has nails in the event that you don't have the power tool), a level, gloves, and safety glasses. It is a good idea to apply sealant to the plywood and make it waterproof.

Start by measuring each window's size and height. Then cut the plywood sheets to fit inside the frames. This is best done on site because you are more in control of the exact dimensions.

Cut the boards to the size you want using a track or circular saw. After installation, you will need to sand them down completely. them. Once your boards are in place put the 3 inch stainless steel hanger screws into the posts that frame each window. Use washers on each bolt, and wing nuts to anchor them. Make sure that each screw penetrates the studs at a minimum of two inches to ensure the board is strong enough to resist strong winds.

If you're building with concrete block, you could instead join the plywood to the building by using galvanized pan-head screws that are driven through the edges that are overlapping of each panel to form masonry blocks or cinder blocks. It is also necessary to drill pilot holes into the masonry before screwing corrosion-resistant screws into the holes. This project can take three hours for each period. It is crucial to begin as soon as a hurricane warning has been issued. This will allow you enough time to complete the project before the storm arrives.

Maintenance

If you're a homeowner or business owner, it is essential to have the necessary materials to secure windows and doors in advance of a severe storm. This will help you to avoid costly repairs and protect your home from further damage that could be caused by rain, wind flying objects, and other causes.

The right materials will make boarding up more efficient and speedier. It is important to measure each window precisely. This will ensure the OSB or plywood is fitted snugly and will not fall off easily. If you're using plywood make sure you use exterior grade sheets, and consider adding a protective finish.

Mark the locations where the screws are going to be put into the board after you have taken measurements of the OSB or plywood. Then, use a drill to pre-drill holes into the plywood at intervals of 12 inches. Then, you can use hanger bolts to secure the boards in a catastrophe situation. After the storm is over and the local authorities have given you the all-clear to go ahead, remove the bolts, but save them in case of 24 hour emergency boarding up.

The next step is to put the plywood panels over the windows. This is a two-person task So be prepared before you start. If you're using wood, make sure you sand the edges so they are smooth and won't scratch your paint or trim. Then, you can attach the frame to the plywood using screws that are corrosion-resistant and fit into the pilot holes. If your home is lined with shingles made of vinyl, it's best to attach the plywood to the shingles, not the wood framing underneath.

In addition to keeping out the elements of weather and water elements, a boarded up window is also an effective way to prevent burglary. Burglars are more likely take aim at a structure with a broken or unlocked window. They're also more likely to attack an establishment that's been fenced off as opposed to one that's not. If you're a retailer owner, this is a matter you must take seriously.